Различия

Здесь показаны различия между двумя версиями данной страницы.

--- equipment:embedded:voipac_pxa270_baseboard [2012/04/24 12:16]
sergey
+++ equipment:embedded:voipac_pxa270_baseboard [2025/02/20 12:29] (текущий)
@@ Строка 3: / Строка 3: @@
   * http://www.voipac.com/
   * [[http://www.lancesimms.com/PXA270Tips.html|Marvell PXA270 and ARM Microprocessor Tips]]
+{{equipment:embedded:voipac_pxa270_27m-dmm-144_l.jpg?200|}} {{equipment:embedded:voipac_pxa270_27m-dmm-144_l_b.jpg?200|}}
+{{ :equipment:embedded:voipac-pxa270-src.zip |}}
+{{ :equipment:embedded:voipac-pxa270-docs.zip |}}
+{{ :equipment:embedded:voipac-pxa270-bin.zip |}}
+PXA270M DIMM Module Basic specification:
+  * PXA270M / 312MHz
+  * 64MB NAND Flash (16bit)
+  * 64MB SDRAM (32bit)
+  * Audio AC'97 with controller and support for touchscreen
+  * 10/100 Mbps Ethernet
+  * 121 GPIOs
+  * 200pin SODIMM connector
+  * JTAG connector pads
+  * Power supply 3.3V with flexible PMIC
+  * Dimensions 67.6 x 38.0mm
+  * 0°C to +70°C commercial temperature range
+PXA270M DIMM Module Pro specification:
+  * PXA270M / 520MHz (by default set to 312MHz)
+  * 128MB NAND Flash (16bit)
+  * 128MB SDRAM (32bit)
+  * Audio AC'97 with controller and support for touchscreen
+  * 10/100 Mbps Ethernet
+  * 121 GPIOs
+  * 200pin SODIMM connector
+  * JTAG connector pads
+  * Power supply 3.3V with flexible PMIC
+  * Dimensions 67.6 x 38.0mm
+  * 0°C to +70°C commercial temperature range
 ===== buildroot config =====
+make menuconfig
+<code>
+Target Architecture (arm)
+Target Architecture Variant (xscale)
+Target ABI (OABI)
+Build options
+[*] Enable compiler cache
+System configuration
+  (em5) System hostname
+  (ttyS0) Port to run a getty (login prompt) on
+  Baudrate to use (38400)
+Filesystem images
+[*] jffs2 root filesystem
+[*]   Do not use Cleanmarker
+Kernel
+  Kernel binary format (zImage)  --->
+</code>
+make uclibc-menuconfig
+<code>
+Target Architecture Features and Options
+  [*]   Target CPU has a floating point unit (FPU)
+Networking Support
+  [*]     Remote Procedure Call (RPC) support
+</code>
+make linux-menuconfig
-===== Pxa270 DMA =====
-  * 32 DMA channels, DMA[31:0]
-  * supports flow-through and fly-by transfer
-  * 32 channels, 68 PBP (peripherial-bus peripherals) requests, 3 IBP (internal-bus peripherals, only quick-capture interface in this chip) requests, and 3 external device requests.
-A **companion chip** is defined as a device that has the ability to
-control the external bus, whereas an external peripheral must be controlled by the memory
-controller.
 ==== Приотритеты каналов ====
@@ Строка 27: / Строка 80: @@
 controller register bits:
 <code>
-Read:
+Write to device:
 DCMDx[FLYBYS] and DCMDx[FLYBYT] = 0
 DSADRx[SRCADDR] = memory address
@@ Строка 36: / Строка 89: @@
 DCMDx[FLOWTRG] = 1
-Write:
+Read to memory:
 DCMDx[FLYBYS] and DCMDx[FLYBYT] = 0
 DSADRx[SRCADDR] = internal peripheral address
@@ Строка 45: / Строка 98: @@
 DCMDx[FLOWTRG] = 0
 </code>
+All companion-chip-related transfers must use 64-bit aligned addresses for both source and target
+locations.
+Restricting memory addresses to 8-byte boundaries can be helpful because the DMA controller
+encounters overhead while it works with misaligned data. Align the source and target addresses to
+-byte boundaries for optimal DMA controller and memory controller performance.
+By default, during data transfers the DMA controller forces the least significant three bits of all
+external addresses to zeros and the least significant two bits of all peripheral addresses to zeros.
+Software must activate the alignment register to activate byte-aligned addressing.
+**Companion Chip to Memory:**
+Source Alignment (Bytes) : 8 \\
+Target Alignment (Bytes) : 8 \\
+DCMD [IncSrcAddr] (Binary) : 0 or 1 \\
+DCMD [IncTrgAddr] (Binary) : 1 \\
+DCMD[Width] (Binary) : 00
+The companion chip or external peripheral must be connected as a variable-latency I/O memory.
+If either DCMDx[IncSrcAddr] or DCMDx[IncTrgAddr] is set, then the DMA controller
+increments the source or target address, after each bursting transaction, by a number equal to the
+transaction burst size (8, 16 or 32 bytes) or DCMDx[Len]. The latter is used if DCMDx[Len] is
+less than the burst size.
+DCMD_WIDTH must be 0b00 for memory-to-memory moves or companion-chip-related operations.
+---
+===== Под Linux =====
+Состояние регистров DMA смотри в debugfs: /debug/pxa_dma/channels/0/state
+Большинство полезных функций уже определены в файлах
+  /arch/arm/plat-pxa/dma.c
+  /arch/arm/plat-pxa/include/plat/dma.h
+так что изобретать свои велосипеды нет необходимости.

SPASCHARM

Инструменты пользователя

Инструменты сайта

Различия

Инструменты страницы